What happens on an edgebander servicing visit
Servicing is the unglamorous work that a busy production week never leaves time for. An edge banding machine spends its life in dust and hot glue, and both end up where they shouldn't, packed round moving parts and caked on the rollers. Routine cleaning and maintenance is a big part of every service, and it's more important than it sounds, because you can't judge the condition of a part you can't see. If the glue pot or rollers need proper attention, that's work we do as well.
We check the feed system too, because if panels aren't travelling straight and held firmly, nothing further down the machine can do its job, however well it's set. There are mechanical and electrical adjustments to make, putting back what has crept out of place since the last visit, and while the covers are off we look the whole machine over for wear, anything out of line, and any trouble with the glue or the feed. So by the end you know the real condition of the machine, and what's likely to need attention next.
You'll get our honest view of how it's running and what it needs, plus what we'd do to head off the next breakdown. It's your call what happens next, and we'll always explain why we've suggested something.
Every three to six months, going by how much it runs
That's the interval we suggest, and where your machine sits in that range is mostly about workload. One working long days, every day, puts far more panels through it and far more glue through the pot, so it'll want looking at nearer the three month end. A machine that only runs a couple of days a week can usually sit nearer six. If you're not sure which camp yours falls into, the state of the glue pot and the edges coming off at the end of a shift will tell you a lot, and we'll gladly give you our view.
What a missed service starts to look like
You'll usually spot the slow slide on the panels. The glue line gets a little thicker or darker than it used to be, the edging starts lifting at a corner here and there, or the trim leaves a faint ripple you can feel with a fingertip. Sometimes it's the feed, with boards starting to wander, or the edging gripping well at the front of a panel and not at the back. And if you look in the pot, the glue may have gone dark and lumpy.
None of those is a disaster on its own, and a service is the right time to find out which ones are simple adjustments and which need more work, such as calibrating the trimming units. The trouble is that it's easy to get used to them and work around them, right up until something finally stops the machine. If you're seeing two or three at once, it's worth booking a service now rather than waiting for the date on the calendar.
Keeping it right between our visits
A good service lasts much longer when the people running the machine every day look after it in between. That means the cleaning your manufacturer's manual sets out, always done with the machine switched off and isolated as the manual says, and simply paying attention to how it looks and sounds. Anything beyond that, inside the units or the electrics, is for an engineer.
If your team would like to get better at the day to day side, our Preventative Maintenance and Glue System Maintenance courses are run on site, for one operator or the whole team. You'll find all six courses on our training page.
Servicing and our Care plans
You can simply book a service whenever it's due, but if you'd like someone keeping an eye on the dates for you, both our monthly plans help. Care, at £149 plus VAT a month, reminds you when a service is coming up and gets you a better rate when you book one. Care+, at £249 plus VAT a month, goes further, with help planning your servicing and preventative maintenance, a machine health check-in every quarter and an annual machine health review. Neither plan includes engineer visits, so a service is still quoted on its own, but once you've paid for 12 months on either, you get half off the labour for one yearly service on a single machine, capped at eight hours. The full details are on our remote support and Care plans page.
Booking a service
We only work on edgebanders, and that covers all the usual names, from Biesse, SCM and Homag to Nanxing, Hebrock, Casadei, Holz-Her, Cehisa, OAV and IMA. If yours isn't among them, it's still worth asking. To book a service for your edge bander, or just to check whether it's due, ring 07961 849601. If something is already playing up and you'd like an engineer to see a video and the alarm codes before you decide, a £95 plus VAT remote call is a good place to start. That's 45 minutes going through it together, and if it can't be sorted in that time, £45 comes off the site visit.

