A line running two shifts a day and a machine that only comes on twice a week live very different lives, yet it's easy to give them the same service date just because that's what the sticker on the side says. We'd normally say an edgebander should be serviced every three to six months, and where yours belongs in that range comes down to how much work it does and what you put through it.

That range is where you start, not where you finish, so spend a few minutes placing your own machine in it. Get that right and you're not paying for visits it doesn't need, or finding out the hard way that it needed one sooner.

Count the hours it runs, not the months

The calendar is a rough stand-in for what actually wears an edge bander out, which is running time and the number of panels through it. Six months on a single day shift is a very different workload from six months of double shifts, even though the date on the sticker looks the same. If your machine's control keeps a record of running hours, jot the figure down every time it's serviced, because then you're comparing like with like from one visit to the next.

As a rough way to place yourself, a machine that runs one shift a few days a week can usually go towards six months, one on two shifts or running most of the day and night belongs nearer three, and a single shift every weekday falls somewhere in between. That's only a rough guide, though, and two machines on identical hours can still need very different attention, depending on what they're running and how they're treated.

What brings the next service forward

Glue is the big one. Hot melt EVA is forgiving, but if a pot is left sitting at temperature through long idle spells, the glue darkens and chars, and that burnt residue ends up on the rollers and in the pot. PUR is a different animal. It cures with moisture, and once it's set it won't melt again the way EVA does, so it has to be purged or cleaned out before the machine stands for any length of time, the way the glue maker and your manual set out. Either way, a machine that has had a hard time with its glue will want looking at sooner.

What you band matters too. Dusty boards like MDF and chipboard put a lot of fine dust through an edge banding machine, and it builds up wherever there's glue or moving parts to catch it. Thicker edging and solid wood lipping make the trimming units work harder than thin tape does, so their tooling and settings have more to cope with. And if your team swaps between edging thicknesses and board sizes several times a day, every changeover is a chance for a setting to be nudged and not quite put back.

Then there's the machine itself. An older edgebander with a lot of hours behind it has more parts that are part way worn, so small changes show up sooner. Poor extraction or a dusty corner of the workshop speeds everything up as well. None of these means you have to jump straight to three months, but if two or three of them apply to you, it makes sense to aim for the shorter end.

If it's your only edgebander

Ask yourself what happens to the rest of the shop when this machine stops. If you've got one edgebander and every cabinet, worktop and panel goes through it, a day with it down is a day with everything else stuck behind it. A workshop with two machines can usually shift the work across while one is being looked at, so a slightly longer interval carries less risk there.

With only one, it's worth erring on the sooner side, because when it does stop there's nothing to move the work onto. Think about your busy seasons too. If you know a big run of work or a contract with tight deadlines is coming, get the service done just before it starts rather than halfway through, when the machine is under the most pressure and a breakdown would hurt the most.

The maker's schedule still comes first

Your machine's manual will have its own list of daily, weekly and monthly jobs, things like cleaning, lubrication and checking the air, always done with the machine isolated, and a service from us doesn't replace any of that. The service is the deeper look on top, where an engineer goes round the whole machine, finds the wear and drift your operators wouldn't be expected to spot, and puts right whatever has crept out of adjustment. There's more on what that covers on our servicing page.

Each one makes the other go further. A machine that's kept clean and looked after every day by the people who run it gets far more out of each service, and the interval can sit comfortably at the longer end, while one that only gets attention when an engineer turns up tends to slide the other way. If you'd like your team to feel surer of the everyday side, we run a Preventative Maintenance course on site, for one person or everyone who uses the machine, and it's listed with our other courses on the training page.

When it can't wait for the date

Sometimes the machine tells you it's due before the calendar does, and you'll often hear it from your operators first. They're tweaking the same setting every morning, or an alarm keeps clearing and then coming back a few days later, or more spoiled panels are going in the offcut bin than there used to be. Each of those is small, and it's easy to keep working round them for weeks, so if you're noticing them, don't sit tight until the date comes round.

Fitting servicing around production

Nobody wants a machine out of action in the middle of a busy week, so plan the visit for a quieter day or a planned shutdown where you can. It also helps to agree the rough date of the next service before the engineer leaves, while everyone has the machine fresh in mind, rather than relying on someone remembering in five months' time.

Keep a simple record next to the machine or on the shared drive: the date of each service, the running hours if you have them, what was done and anything that was flagged to watch. It takes two minutes, and it means that the next time someone asks when the machine was last done, there's an actual answer. And if anything big changes, such as moving the machine, a major repair, or switching to a new type of edging or glue, have it checked sooner than planned instead of waiting for the date.

If you'd rather not track the dates yourself, Care (£149 a month plus VAT) sends you service and maintenance reminders, and Care+ (£249 a month plus VAT) includes help planning your servicing and maintenance. Neither includes the visit itself, and the full terms are on the Care plans and remote support page.

Getting the next one in the diary

Edgebanders are the only machines we work on, and we travel to workshops all over the UK. If you can't decide whereabouts in the three to six month range your machine belongs, ring 07961 849601 and talk it through with us, and we'll give you an honest view. If something's already playing up, book a remote call instead. You get 45 minutes with an engineer for £95 plus VAT, working through your photos, video and alarm codes alongside your operator, and if the fault isn't sorted in that time, you get £45 knocked off the site visit.